W sart up. ok.

Secopndary Start up ok.

IRTC start up ok.

System OSS start Up and hexapod control ok.

load hexapod positions [0.78,-1.720,-0.180,-192.4,36.2,0].
load board set up IRTC_v10

RON TEST

ALL ON.


SUMMARY ------------------------------------
ccd39 - binning 1
Speed: 2500 kpix/sec - RON (ADU): 24.02 - RON (e-): 12.01 (estimated)
Speed: 890 kpix/sec - RON (ADU): 15.17 - RON (e-): 7.59 (estimated)
Speed: 400 kpix/sec - RON (ADU): 8.59 - RON (e-): 4.29 (estimated)
Speed: 150 kpix/sec - RON (ADU): 10.37 - RON (e-): 5.18 (estimated)

COPLEY OFF


SUMMARY ------------------------------------
ccd39 - binning 1
Speed: 2500 kpix/sec - RON (ADU): 19.01 - RON (e-): 9.50 (estimated)
Speed: 890 kpix/sec - RON (ADU): 13.34 - RON (e-): 6.67 (estimated)
Speed: 400 kpix/sec - RON (ADU): 7.88 - RON (e-): 3.94 (estimated)
Speed: 150 kpix/sec - RON (ADU): 8.65 - RON (e-): 4.32 (estimated)

Test Close loop.
Fault applying loop control parameters: bin,loop freq,TT:
command RefineAO failed with status EXECUTION FAILED.
aDoPT EXCEPTION: fRAMERATE 0 IS OUT OF RANGE FOR BINNING 1X1(-5002) VALUE_OUT_OF_RANGE_ERROR

binning:1
lOOP freq: 800hZ.
Lmabda:3.0
FAULT MESSAGE DEAMON wfs and secondary down. The systems has to be restarted again

ACQUIRE NEW INTMAT AT BIN 1.

Generate the disturbance.
CmdDist _2001105_114312.

KL
Nmodes:400
Bin:1.
Freq:400Hz.

Acquire Intmat.

KL.
CmdDist_114312
itr:4
loop freq:400Hz

Analyse Intmat. good used to acquire another intmat. Rec_20051105_115003

Acquire Intmat at close loop.
KL
cmddist_
Iter:4.
freq:400
cloe loop matrix:Rec_20051105_115003
Gain vector: gain0.05

Analyse Intmat.

REC_20051105_120030...BIN:1..... 400Hz.......2L/D

note: windy,.. the gain up to 0.5.

rec_120419 only TT ...
Acquire Intmat rec_20091105_120810.


using the rec_120419 in close loop.
gain:0.3

test close loop bin 4 at low flux. about 80phot/subap the secondary starts to go off.
It has been seen that there still the error of the subaperture (right up corner black-white), odd problem of the number of subapertures.
CLOSE LOOP TEST.

A series of close loop diagnostics has been taken, the system worked well with the performnaces described in the table below .

there are not images of the IRTC

SUMMARY...

mag loophz bin seeing l/D SR BASELINE
7.2 1000 1 1 2 68%
7.2 1000 1 0.8 2 76%
7.2 1000 1 0.8 3 80%
7.2 1000 1 0.6 3 80%
7.2 1000 1 0.6 2 79%
9.4 1000 1 0.8 2 77% 73(SIMUL),59(SIMUL+TS)
9.4 1000 1 1 2 63%
9.4 1000 1 0.6 2 73%
10.4 800 2 0.8 3 48% 61(SIMUL),50(SIMUL+TS)
10.4 800 2 0.6 3 55%

FAULT: RIP SECONDARY. IMPOSIBLE TO RECOVER THE FAULT USING THE RECOVER FAILD.
SECONDARY TURN OFF AND IDL CONTROLLER OFF.

BIN 2 INT MAT.

Cmddist_20091105_165340.

Loop:400
Nmodes:153
PP: frames:5, cycle:1
gain:optimized_2L

Acquire IntMat.
KL
cmddist_165340.
Iter:4
loop:400Hz.

Analyse the intmat: the first 4 modes are missed and the last four are close to zero. NOT GOOD.

W sart up. ok.

Secopndary Start up ok.

IRTC start up ok.

System OSS start Up and hexapod control ok.

load hexapod positions [0.78,-1.720,-0.180,-192.4,36.2,0].
load board set up IRTC_v10

RON TEST

ALL ON.


SUMMARY ------------------------------------
ccd39 - binning 1
Speed: 2500 kpix/sec - RON (ADU): 24.02 - RON (e-): 12.01 (estimated)
Speed: 890 kpix/sec - RON (ADU): 15.17 - RON (e-): 7.59 (estimated)
Speed: 400 kpix/sec - RON (ADU): 8.59 - RON (e-): 4.29 (estimated)
Speed: 150 kpix/sec - RON (ADU): 10.37 - RON (e-): 5.18 (estimated)

COPLEY OFF


SUMMARY ------------------------------------
ccd39 - binning 1
Speed: 2500 kpix/sec - RON (ADU): 19.01 - RON (e-): 9.50 (estimated)
Speed: 890 kpix/sec - RON (ADU): 13.34 - RON (e-): 6.67 (estimated)
Speed: 400 kpix/sec - RON (ADU): 7.88 - RON (e-): 3.94 (estimated)
Speed: 150 kpix/sec - RON (ADU): 8.65 - RON (e-): 4.32 (estimated)

Test Close loop.
Fault applying loop control parameters: bin,loop freq,TT:
command RefineAO failed with status EXECUTION FAILED.
aDoPT EXCEPTION: fRAMERATE 0 IS OUT OF RANGE FOR BINNING 1X1(-5002) VALUE_OUT_OF_RANGE_ERROR

binning:1
lOOP freq: 800hZ.
Lmabda:3.0
FAULT MESSAGE DEAMON wfs and secondary down. The systems has to be restarted again

ACQUIRE NEW INTMAT AT BIN 1.

Generate the disturbance.
CmdDist _2001105_114312.

KL
Nmodes:400
Bin:1.
Freq:400Hz.

Acquire Intmat.

KL.
CmdDist_114312
itr:4
loop freq:400Hz

Analyse Intmat. good used to acquire another intmat. Rec_20051105_115003

Acquire Intmat at close loop.
KL
cmddist_
Iter:4.
freq:400
cloe loop matrix:Rec_20051105_115003
Gain vector: gain0.05

Analyse Intmat.

REC_20051105_120030...BIN:1..... 400Hz.......2L/D

note: WINDY, IT HAS TO BE DONE AGAIN...,.. the gain up to 0.5.

rec_120419 only TT ...
Acquire Intmat rec_20091105_120810.


using the rec_120419 in close loop.
gain:0.3

DURIN

Test close loop bin 4 at low flux. about 80phot/subap the secondary starts to go off.
It has been seen that the error of the subaperture
CLOSE LOOP TEST BIN 1. WITH THE RECONSTRUCTOR REC_20091005_111109 400 MODES 2L/d

A series of close loop diagnostics has been taken, the system worked well with the performnaces described in the table below .
IT HAS BEEN SHOWED A GOOD PERFORMANCES .

there are not images acquired of the IRTC

SUMMARY...

mag loophz bin seeing l/D SR BASELINE
7.2 1000 1 1 2 68%
7.2 1000 1 0.8 2 76%
7.2 1000 1 0.8 3 80%
7.2 1000 1 0.6 3 80%
7.2 1000 1 0.6 2 79%
9.4 1000 1 0.8 2 77% 73(SIMUL),59(SIMUL+TS)
9.4 1000 1 1 2 63%
9.4 1000 1 0.6 2 73%
10.4 800 2 0.8 3 48% 61(SIMUL),50(SIMUL+TS)
10.4 800 2 0.6 3 55%

FAULT: RIP SECONDARY. IMPOSIBLE TO RECOVER THE FAULT USING THE RECOVER FAILD.
SECONDARY TURN OFF AND IDL CONTROLLER OFF.

WORKING ON THE MODIFICATION FOR BIN 2 AND BIN 4


Cmddist_20091105_165340.

Loop:400
Nmodes:153
PP: frames:5, cycle:1
gain:optimized_2L

Acquire IntMat.
KL
cmddist_165340.
Iter:4
loop:400Hz.

Analyse the intmat: the first 4 modes are missed and the last four are close to zero.
Possible problem during the generation of the disturbance and number of modes to correct.

Another try with a new disturbance.

BIN 2 .

Cmddist_20091105_175632
Rec to use in close loop acquire intmat. Rec:20091105_175332.
400Modes. reduced to 153 modes
400Hz.
3L/D
gain:gain0.05.

.........REC_20091105_175922......BIN 2.....400Hz....3L/D....153 modes

GOOD UP TO 0.7.

testing the close loop with the disturbance on, the system works ok. Working at 160 phot/subap the syswtem didn't close the loop, start to skip frame at gain:0.3.
Load a flat, and closing the loop without disturbance the system only reachs to go up to 0.3...and it was impossible to get the the same performances than before.
fault: the adaptative secondary mirror interface gui can not be loaded.

CLOOP <_182204>
_
IRTC dark = <>
IR exp = us
IR n frames =
Bin = <2>
LoopHz = <800>
Pup = <tracking#>
Dist =<_0.8_ovfreq_1000>
Gain = <-0.8>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 600 phot/subap
Staged: <OFF>
Nota = <.SR:53%...Problem with the slopes, the gain applied is negative. Check procedure to calculate the slopes.............>

CLOOP <_182429>
_
IRTC dark = <>
IR exp = us
IR n frames =
Bin = <2>
LoopHz = <800>
Pup = <tracking#>
Dist =<_0.8_ovfreq_1000>
Gain = <-0.8>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 160 phot/subap
Staged: <OFF>
Nota = <.SR:%..wrong...Problem with the slopes, the gain applied is negative. Check procedure to calculate the slopes...........>
corrected the error FOR THE BIN 2 in the slope program.

TEST OF THE NEW CORRECTIONS BIN2.

CLOOP <_183901> GOOD... .....

_
IRTC dark = <>
IR exp = us
IR n frames =
Bin = <2>
LoopHz = <800>
Pup = <tracking#>
Dist =<_0.8_ovfreq_1000>
Gain = <0.5>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 160 phot/subap
Staged: <OFF>
Nota = <.SR:51%............>

CLOOP <_184026>
_
IRTC dark = <>
IR exp = us
IR n frames =
Bin = <2>
LoopHz = <800>
Pup = <tracking#>
Dist =<_0.8_ovfreq_1000>
Gain = <0.7>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 140 phot/subap
Staged: <OFF>
Nota = <.SR:51%....mag:10.4.........>

CLOOP <_184451>
_
IRTC dark = <>
IR exp = us
IR n frames =
Bin = <2>
LoopHz = <625>
Pup = <tracking#>
Dist =<_0.8_ovfreq_1000>
Gain = <0.7>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 40 phot/subap
Staged: <OFF>
Nota = <.SR:43%....mag:12.1.........>

CLOOP <_184905>
_
IRTC dark = <>
IR exp = us
IR n frames =20
Bin = <2>
LoopHz = <625>
Pup = <tracking#>
Dist =<_0.8_ovfreq_625>
Gain = <0.3>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 20 phot/subap
Staged: <OFF>
Nota = <.SR31%:%....mag:13.1.........>

CLOOP <_184905>
_
IRTC dark = <R:/irtc_data/20091105113332/irtc_00003-4.fit>
IR exp = 500000us
IR n frames =20
Bin = <2>
LoopHz = <625>
Pup = <tracking#>
Dist =<_0.8_ovfreq_625>
Gain = <0.3>
Mod = 3 l/D
Rec = <REC_20091105_175922>
SN = zero/....
FW1 = <600....>
FW2 =
Phot = 20 phot/subap
Staged: <OFF>
Nota = <.SR31%:....mag:13.7.........>

-- JuanCarlosGuerra - 2009-11-05
Topic revision: r6 - 09 Nov 2009, AlfioPuglisi
This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding Foswiki? Send feedback